Searching for the Correct Code
Advertising
Setting One-touch Remote Control Setting Bluetooth Device External Sound Output Settings Selecting speakers to output sound Outputting sound from headphones Controlling the volume of an audio system with the TV’s remote control 10. TV and television manuals and free pdf instructions. Find the user manual you need for your TV and more at ManualsOnline.
It is possible to find a code number available
for a component that does not have one in “
Component code numbers.”
Before starting the Search function
Set each component to the following status so that the Search function works effectively.
TV, DVD Home Theater: Power-on
Other components: Power-off
*
If any of these components are assigned to any
of the Component Select buttons, you can set a component code using the Search function.
1 Press and hold SET for more than two seconds. The SET indicator
lights up.
2 Press the appropriate Component Select button. The SET indicator
lights up.
3 Press CH + (or CH –) and 1 in turn until the component reacts as
follows:
TV: Power-off
Other components: Power-on
Press CH + to go to the next code number.
Press CH – to go back to the previous code number.
The SET indicator flashes once after the numbers have cycled
once. One cycle means, for example, that the commander has finished searching for all the code numbers allocated to the component.
4 Press ENT.
The SET indicator and the Component button turn off.
If the SET indicator flashes five times before turning off, setup is incomplete. Start over from Step 3.
If the component does not operate properly, repeat steps 1 to 4 and
search for another code.
If you still cannot get the Commander to work properly, see
“
Troubleshooting.”
Installing the batteries
Push open the battery compartment and insert two size AA (R6)
batteries (not supplied). Be sure to align the + and – on the batteries with the + and – in the battery compartment.
1
2
When to replace the batteries
Before replacing the batteries, have new ones ready beforehand.
Under normal conditions, batteries will last up to one year. If the Commander does not operate properly, the batteries might be worn out. Replace the batteries with new ones.
Notes
• Replace both batteries with new ones.
• Do not take more than 3 minutes to replace the batteries; otherwise, your
code number settings will be erased.
• Do not mix old batteries with new ones, or mix different battery types together.
• If the electrolyte inside the battery should leak, wipe the contaminated area of
the battery compartment with a cloth and replace the old batteries with new
ones. To prevent the electrolyte from leaking, remove the batteries when you plan to not use the Commander for a long period of time.
Specifications
Operable distance
Approx. 7 m (23 ft) (varies depending on component
manufacturer)
Power requirements
Two size AA (R6) batteries (not supplied)
Battery life
Approx. 1 year (varies depending on frequency of
button use - up to approx. 300 times per day)
Dimensions
Approx. 63
Ч 149 Ч 30 mm (w/h/d)
(2
1
/
2
Ч 5
7
/
8
Ч 1
3
/
16
in)
Mass
Approx. 86 g (3.0 oz) (not including batteries)
Design and specifications are subject to change without notice.
Operating a TV
Operating a digital satellite receiver
2 To switch the output of the digital satellite receiver to the TV. (When
you connect a TV cable or antenna to the receiver, the output switches
between TV and satellite programs.)
3, 4 and 9
To change the channel.
q;
CH +: Channel up.
CH –: Channel down.
qa To tune to the last tuned station.
Operating a cable box
2 To change the input mode.
3, 4 and 9
To change the channel.
q;
CH +: Channel up.
CH –: Channel down.
qa To toggle the current/previous channel.
Continued on reverse side / Continúa en el reverso
About tactile dots
The number 5 button and CH + each have a tactile dot for convenient use.
Note on the VOL +/– and MUTING buttons
The Commander controls or mutes the TV’s volume when you select a visual component. The Commander outputs the signals to control or to mute the TV volume when you have set one of these components.
Notes
• In some cases, you can turn the cable box on/off by pressing CH + or CH – on
the Commander.
• If your cable box can control volume, be sure to set its volume control to a
moderate level. If the volume on the cable box is turned down completely,
you will not be able to adjust your TV’s volume with the Commander.
SET indicator
1
3
4
3
Cable box / Adaptadores para cablevisión
Brand / Marca
Code No. / N.º código
Sony
3101
ABC
9405
Adelphia
3107, 3110
Advanced Newhouse
3107
Altrio
3107
Americast
3105
Atlantic Broadband
3107
Bell South
3105
Blue Ridge
3107
Brigth House
3107
Cablevision
3107
Charter
3107
Comcast
3107
Cox
3107
General Instrument
3103, 9002, 9003, 9004, 9005, 9006, 9007, 9008, 9018,
9022, 9043, 9044
GNC
3105
Hamlin
9022, 9023, 9024, 9025, 9026
Illico
3107
Jerrold
3103, 9002, 9003, 9004, 9005, 9006, 9007, 9008, 9018,
9022, 9043, 9044
Memorex
3106
Motorola
3103, 3110, 3111
NET
9042
Oak
9027, 9028, 9029
Pace
3107
Panasonic
9019, 9020, 9021
Paragon
3106
Philips
3104
Pioneer
3107, 9014, 9015
Pulsar
3106
Regal
9022, 9023, 9024, 9025, 9026
Rodgers
3107
Runco
3106
Scientific Atlanta
3102, 3107, 3108, 3109, 9009, 9010, 9045, 9046
Seren
3107
Sigecom
3107
Susquehanna
3107
Time Warner
3107
Tocom
9016, 9017, 9043
Toshiba
3106
ENT
CH
VOL
INPUT
SET
RECALL
MUTING
TV
CBL/SAT
ENT
CH
VOL
INPUT
SET
RECALL
MUTING
TV
CBL/SAT
Component code numbers /
Números de código de componentes
English
Digital Satellite Receiver, Cable box, TV
The following tables show brand names and their corresponding code numbers.
Español
Sintonizador de recepción vía satélite digital, adaptador para cablevisión, televisor
Las tablas que se presentan a continuación muestran las marcas y los números de código
correspondientes.
Press and hold the SET button for 2 seconds or more to set a Component Code.
Mantenga presionado el botón SET durante 2 segundos o más para ajustar un código de componente.
Digital Satellite Receiver /
Sintonizador de recepción vía satélite digital
DirecTV
Dish Network
HDTV Tuner
Brand / Marca
Code No. / N.º código
Code No. / N.º código
Code No. / N.º código
Sony
3001, 3011, 3012
—
—
DirecTV
3013, 3017, 3018,
—
—
3019, 3023, 3024
Dish Network
—
3010, 3014, 3025
—
GE (General Electric) 3019
—
—
Hitachi
3005
—
—
Hughes
3004
—
—
Humax
—
—
3402
JVC
—
3010, 3014
—
Magnavox
3018
—
—
Panasonic
3003
—
—
Philips
3018
—
—
Proscan
3002, 3007, 3019
—
—
RCA
3002, 3007, 3019, 3021 —
—
Samsung
3017, 3022
—
3404
Sylvania
—
—
Sony Remote Tv Control Manuals
3403
Toshiba
3006
—
Sony Remote Control Instructions
—
Usdigital
—
—
3401
©2007 Sony Corporation Printed in China
English
3-278-786-12(1)
RM-EZ4
Operating Instructions
Manual de instrucciones
(parte posterior)
Remote
Commander
General
1 To set up the Commander.
5 Volume up: +
Volume down: –
6 To mute the volume on a
TV.
7 To turn the power of a
selected component on or
off.
8 Component Select Buttons.
Press to select a component
to operate.
Remote Button Descriptions
Operating a Component
1 Press the appropriate Component Select button on the
Commander.
TV
CBL/SAT
2 Aim the Commander directly at the component.
3 Press the button for the function you want to use.
See “Remote Button Descriptions” for complete descriptions of
the buttons on the Commander.
Notes on Using the Remote Commander
Basically, use this Commander in the same way as the
Commanders supplied with your components. • Using this Commander will not increase the functions of your
components. The functions of the Commander are limited to
the functions of the components themselves. For example, if your TV does not have a MUTING function, MUTING on this Commander will not function with your TV.
• Some functions of the component may not work with this
Commander.
• If your cable box can control volume, be sure to set its volume
to a moderate level. If the volume on the cable box is turned
down completely, you will not be able to adjust your TV’s volume with the Commander.
2
v
This guide shows you how to set the Remote
Commander to operate your components.
Enter the code number
Example: To set up a Philips Digital Satellite Receiver
1
Find the code number in “ Component code numbers.”
If your component is not listed, try the search method described in “Searching
for the Correct Code.”
2
Set the Remote Commander for code input mode.
Press and hold SET for more than two seconds.
The SET indicator lights up.
3
Press the appropriate Component Select button.
CBL/SAT
4
Enter the code number.
5
Finish setting.
Press ENT.
Let's check
6
Turn on the component you want to set up.
7
Press the same Component Select button in step 3 again.
8
Sony Xbr65a8g Remote Control Manual
Aim the Remote Commander at the component and press
1
1
1
1
1
on the Remote Commander.
v
Sony Tv Remote Control User Manual Free
Was the component turned off?
Yes
Check that the other buttons function.
Sony Tv Remote Control User Manual Instructions
No
Start over from Step 2 above, using another code number.
If you still cannot get the Remote Commander to work properly after
trying all the codes listed for your component, try the search method described in “Searching for the Correct Code.”
• If the SET indicator flashes five times before lighting up, it means that the setup is incomplete.
Confirm the code number and start over from Step 4.
• If you do not input anything into the Remote Commander within 20 seconds between each step, or if you
press SET while setting the code number, the setup procedure will be canceled. Start over from Step 2.
Startup Guide
b
b
b
For the customers
in the U.S.A. WARNING
This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the
receiving antenna.
• Increase the separation between
the equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an
experienced radio/TV
technician for help.
You are cautioned that any
changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
Setting Up the Remote Commander
About setting up the Commander
The Commander is set up at the factory to operate Sony brand
components. However, even if you intend to use the Commander with a Sony component, you may still need to set up the Commander for it, depending on the component. To set up the Commander to use with other (non-Sony) manufacturers’ components, or to use with a component that is not preset at the factory, you will need to follow the instructions in this manual to preset the Commander with the correct code number for your component. (See “Startup Guide” and “Component Code Numbers”
.)
Note
The Commander can be set up to operate only one component per button –
unless their code numbers happen to be the same. For example, you cannot set up the Commander to operate a Sony TV and a Panasonic TV simultaneously (because they use different code numbers).
Preset component(s)
TV
Cable box/Digital
satellite receiver/TV
Component Select button
TV
CBL/SAT
Factory setting
Sony TV
Sony Cable box
Troubleshooting
If you have problems setting up or using the Commander:
• When setting up the Commander, carefully go through the procedures
described in “Startup Guide.” If the code that is listed first for your component
does not work, try other codes for that component – in the order in which they are listed. If all the codes fail to work (or if your component is not listed in this manual), try using the procedures in “Searching for the Correct Code.”
• Make sure that you are aiming the Commander directly at the component,
and that there are no obstructions between the Commander and the
component. Sony Tv Remote Control Instructions
• Make sure the batteries you are using are not worn out, and that they are
inserted correctly.
• Check that the appropriate TV or CBL/SAT button is pressed.
• Check that the component has infrared remote capability. For example, if
your component did not come with a remote control, it probably is not
capable of being controlled by the Remote Commander.
• Should any problem persist, reset the Commander to the factory setting by
pressing the 1, INPUT and VOL – buttons simultaneously.
For the customers in the U.S.A.
Customer Support Information
After you have read through this manual, if you still cannot get the Remote
Commander to work properly, call the Sony Customer Support Helpline at 1-800-822-2217.
2
3
4
5
Code No. / N.º código
c
c
ENT
SET
TV
CBL/SAT
2 To change the input mode.
3, 4 and 9
To change the channel.
q;
CH +: Channel up.
CH –: Channel down.
qa To operate the JUMP, FLASHBACK or CHANNEL RETURN function on
the TV.
c
ENT
b
Advertising
Popular Brands
Popular manuals
Comments are closed.
|
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |